Accepted papers

 

	Paper title	Author(s)	Company, Institution	Country	Final Paper status March 30th 2005
305	Optimisation of Cutting Conditions in the Computer Aided Tool Management System	MURŠEC B., PLOJ T.	University of Maribor Faculty of Agriculture	Slovenia	Accepted
307	Modelling fibre breakage in a single screw extruder	MOGUEDET M., APALOO R., BALCAEN J., BEREAUX Y., CHARMEAU J. - Y.	Site de Plasturgie de l’INSA de Lyon	France	Accepted
310	Analysis of Thin-wall Injection Moulding Process	GODEC1  D.,  ROT2 M., ŠERCER1 M.	University of Zagreb Faculty of Mechanical Engineering and Naval Architecture1 University of Ljubljana, Faculty of Mechanical Engineering2	Croatia1 Slovenia2	Accepted
311	Friction in Tube Hydroforming - Analytical  Modelling and Fe Simulation	PLANČAK1 M., VOLLERTSEN2 F., WOITSCHIG2 J.	University of Novi Sad – FTN1 BIAS2	Serbia and Montenegro1 Germany2	Invited paper
312	Use of Finite element method simulation to shorten measurement cycle of sheet-metal parts with residual stresses	ZAIMOVIĆ – UZUNOVIĆ N.,  LEMES S.	Faculty of Mechanical Engineering in Zenica	Bosnia and Herzegovina	Accepted
314	Thermo mechanical Rolling of Dual Phase Steel Strips	DZEDZIC M., TURCZYN S.	University of Science and Technology Krakow	Poland	Accepted
315	Hybrid Manufacturing Process for Rapid High Performance Tooling	ERNST G. KERSCHBAUMER M.,	Laserzentrum Leoben JOANNEOM RESEARCH GmbH	Austria	Accepted
316	Finite element analysis of upsetting problems using elasto-plastic and rigid-plastic material model	CVITANIĆ V. VLAK F., LOZINA Ž.	University of Split, Faculty of Electrical and Mechanical Engineering and Naval Architecture	Croatia	Accepted
317	Development of new plastic product with CAE tools	BUJANIĆ B., ŠERCER M., RUJNIĆ-SOKOLE M.	University of Zagreb Faculty of Mechanical Engineering and Naval Architecture	Croatia	Accepted
318	Bulk Metal Forming by Local Heating	OKMAN1 O., ÖZMEN1 M., HUWILER2 H., WEIDIG3 U.,TEKKAYA1 A. E.	METU Department of Mechanical Engineering1 RUAG Components Altdorf2 University Kassel, Lehrstuhl für Umformtechnik3	Turkey1, Switzerland2 Germany 3	Invited paper
319	Influence of the fuzzy model sugeno parameters for prediction of the lifetime of relanex insulating material	HAMMER M., SZABO R., SVOBODA J.	Brno University of Technology Faculty of Mechanical Engineering	Czech Republic	Accepted
320	Multi-stage forming simulation	TISZA1 M., LUCKAS2 Z., TISZA1 M. jr	University of Miskolc Department of Mechanical Engineering1 MTA ME Mechanical Technological Research Group2	Hungary1,2	Invited paper
321	The use of cooperation and Networking in the Die and Mould industry - A. Comparison between Portugal, Spain and Sweden	JOHANSSON C.	Lulea University of Technology Department of materials and manufacturing engineering	Sweden	Accepted
322	A Continuum Damage Model for Lifetime Prediction of H11 Tool Steel	VELAY V., BERNHART G., DELANGES D., PENAZZI L.	Research Centre on Tools Materials and Processes Ecole des Mines d’Albi-Carmaux	France	Accepted
325	Effects of alloying elements on carbides precipitation and fatigue properties of modified AISI H11 hot-work tool steels	MICHAUD1, 2, 3 P., DELAGNES1, 2 D., LAMESLE1 P., RICHY3 P.-E., LEVAILLANT2 C.	Centre de Recherche Outillages, Materiaux et Procedes (CROMeP)1 Centre d’Elaboratino de Materiaux et d’etudes Structurales2 Aubert&Duval, Groupe Recherche et Developpment3	France	Invited paper
326	Radial gear extrusion analysis, FE modelling and experimental verification	SKUNCA1 M., SKAKUN2 P., MATH1 M.	University of Zagreb Faculty of Mechanical Engineering and Naval Architecture Chair of Metalforming1 University of Novi Sad Faculty of Technical Sciences Institute for Production Engineering2	Croatia1 Serbia and Montenegro2	Accepted
328	Influence of Regulated Cyclic heat treatment on properties of carbonised steels	MARUŠIĆ V., D. KRUMES	University of Osijek, Faculty of Mechanical Engineering	Croatia	Accepted
329	Innovative Process Chains to Fabricate Hollow Shafts by Partial Forming	NEUGEBAUER R., LORENZ B., M. KOLBE, R. GLASS	Fraunhofer Institute for Machine Tools and Forming Technology	Germany	Accepted
330	Indirect rapid tooling with aluminium and milled fibre reinforced resins	LINO1 J., VASCONCELOS2 P. V., NETO3 R. J.	FEUP Faculdade  de Engenharia da Universidade do Porto, DEMEGI1 ESTG/IPVC Instituto Politecnico de Viana do Castelo2 INEGI – Instituto de Engenharia mecanica e Gestao Industrial3	Portugal	Accepted
331	New materials for tooling in sheet metal forming - a study of usability and robustness of polymer and wood materials	PINTO1 M., SANTOS1, 2 A. D., TEIXERA1 P., BOLT3 P. J., SANTOS4 P.	INEGI Institute of mechanical Engineering and Industrial1  Department of Mechanical Engineering and Industrial Management University of Porto2 TNO Science and Technology Eindhoven3 PJFerramentas, R. Paz, Quinta do Loureiro Cacia4	Portugal1, 2, 4 The Netherlands3	Accepted
333	A study on design and performance of hybrid moulds for injection moulding	PONTES1 A. J., QUEIROS2 M. P., BARTOLO2 P., POUZADA1 A. S.	Institute for Polymers and Composites Department of Polymer Engineering, University do Minho1 Department of Mechanical Engineering, Instituto Politecnico de Leiria2	Portugal	Accepted
335	Laser repair welding of moulds and dies	TUŠEK1 J., HRŽENJAK2 M., POMPE2 K., MULC3 M.	Faculty of Mechanical Engineering in Ljubljana1 TKC2, d. o. o. Kovinoplastika Lož d. d. 3	Slovenia	Invited paper
336	Development of weld-cladding processes for surface enhancement of hot-work tooling	TALAMINI A., TUŠEK J., TALJAT B.	STEEL d. o. o.	Slovenia	Accepted
337	Determination of forming limit diagrams in CAE Environment	PEPELNJAK T., A. PETEK, K. KUZMAN	Faculty of Mechanical Engineering in Ljubljana	Slovenia	Accepted
339	Improvement the Accuracy of side and bending in two stages	GRIZELJ1 B., KENTER2 I. M.	University of Osijek, Faculty of Mechanical Engineering1 Institut für Produktionstechnik und Fabrikbetrieb, High Technical School Bremen2	Croatia1 Germany2	Accepted
341	Generation of parameter technologies for the EDM die sinking with artificial neural networks (ANN) and non-linear regression functions (NRF)	JUHR H., KÜNANZ K., NESTLER A., LEITTE G.	Dresden University of Technology, Institute for Production Engineering	Germany	Invited paper
343	Coated forming tool steel and the influence of surface roughness	PODGORNIK1 B., HOGMARK2 S.	Faculty of Mechanical Engineering Centre for Tribology and Technical Diagnostics University of Ljubljana1 Uppsala University The Tribomaterials Group	Slovenia1 Sweden2	Accepted
346	The application of finite volume method to analyse of tool - work piece interaction during cold extrusion	BAŠIĆ H.	University of Sarajevo, Faculty of Mechanical Engineering	Bosnia and Herzegovina	Accepted
347	Mathematical modelling of the hardness variation of pieces subjected to heat treatment after warm working	BICHTAS1 C. M., NEGREA2 G.	Technological Educational Institute of Piraeus Department of Physics, Chemistry and Materials Technology1 Technical University of Cluj-Napoca, Faculty of Materials Science and Engineering2	Greece1 Romania2	Accepted
348	Concurrent Engineering by Development and Production of a new 3D tool	KOPAČ J. DOLINŠEK S.	Faculty of Mechanical Engineering in Ljubljana	Slovenia	Invited paper
349	Microstructures of nitrided surfaces of dies for Al-hot extrusion and their influence on die endurance	TERČELJ M., KUGLER G., VEČKO-PIRTOVŠEK T., TURK R.	Faculty of Natural Science and Engineering	Slovenia	Accepted
351	Properties of cutting ability of the nitride tool ceramics coated by PVD and CVD coatings	DOBRZANSKI1 L. A., PAKULA1 D., KOPAČ2 J., SOKOVIĆ2 M.	Silesian University of Technology Institute of Engineering Materials and Biomaterials Gliwice1 University of Ljubljana Faculty of Mechanical Engineering2	Poland1 Slovenia2	Invited paper
352	On-line control of the wire material properties by means of straightening	NASTRAN M., K. KUZMAN	Domel d. d.	Slovenia	Accepted
353	Effects of depositing multilayers on properties of the selected cemented carbides, cermets and tool ceramics	DOBRZANSKI1 L. A., MIKULA1 J., GOLOMBEK1 K., KOPAČ2 J., SOKOVIĆ2 M.	Silesian University of Technology Institute of Engineering Materials and Biomaterials Gliwice1 University of Ljubljana Faculty of Mechanical Engineering2	Poland1 Slovenia2	Accepted
354	Influence of debinding process on microstructure and properties of HS6-5-2 HSS parts produces by powder injection moulding	DOBRZANSKI1 L. A., MATULA1 G., HERRANZ2 G., VAREZ2 A., LEVENFELD2 B., TORRALBA2 J. M.	Silesian University of Technology Institute of Engineering Materials and Biomaterials Gliwice1 Departemento Ciencia de Materials e Ingenieria Metalurgica Escola Politecnica Superior Universidad Carlos III de Madrid2	Poland1 Spain2	Accepted
355	Employment of neural networks for modelling of corrosive wear of hard magnetic composite materials	DOBRZANSKI L. A., DRAK M., TRZASKA J.	Silesian University of Technology Institute of Engineering Materials and Biomaterials Gliwice	Poland	Accepted
356	Effect of processing conditions on structure formation of polymers	EMIR I., FLORJANIČ U.	Faculty of Mechanical Engineering University of Ljubljana	Slovenia	Invited paper
357	Review of possibilities for rapid multiplication of complex objects	PAHOLE I., I. DRSTVENŠEK, J. BALIČ	Faculty of Mechanical Engineering in Maribor	Slovenia	Accepted
358	Monitoring and Control of Material Flow in a Company	BERLEC T., KUŠARJ., STARBEK M.	Faculty of Mechanical Engineering University of Ljubljana	Slovenia	Invited paper
360	Scheduling of Operations in Distributed Production Units	BREZOVAR A., KUŠAR J., TOMAŽEVIČ R.,STARBEK M.	Faculty of Mechanical Engineering University of Ljubljana	Slovenia	Accepted
362	Tooling systems and peripheral equipment for the precision forging of flat long pieces with perform operations	BEHRENS B.-A., REINSCH S., SCHOTT A., SPECKER A.	Institut für Integrierte Produktion Hannover GmbH (IPH)	Germany	Accepted
363	The effect of Powder Injection Moulding parameters on the green part geometry	BERGINC1 B., KAMPUŠ1 Z., ŠUŠTARŠIČ2 B.	Faculty of Mechanical Engineering in Ljubljana1 Institute of metals and technology LJubljana2	Slovenia	Invited paper
364	The use of Fe simulations in manufacturing of stamping tools – an industrial example	GANTAR1 G., HARING2 A., VREŠ2 A.., HODŽIČ2 S., PUC2 M.	Faculty of Mechanical Engineering in Ljubljana1 Gorenje Orodjarna d. o. o. Velenje2	Slovenia	Accepted
365	Deep - drawing - die platform with the adjustable multipoint - supporting structure	OHASHI T.,	AIST, Digital Manufacturing Research Center	Japan	Accepted
369	Virtual production as a guideline towards competitive mould making	NARDIN B.	TECOS Slovenian Tool and Die Development Centre	Slovenia	Keynote paper
370	Influence of material choice in 2 component technologies	ŠMUC B., NARDIN B.	TECOS Slovenian Tool Development cetre	Slovenia	Accepted
371	Application of numerical simulation in the design vital loaded structure	RADIŠA1 R., OBRADOVIĆ1 I., JARAMAZ2 D., BELIČEV3 P.	LOLA INSTITUTE1 Faculty of civil engineering management2 VINČA Institute for nuclear sciences, Laboratory of Physics3	Serbia and Montenegro	Accepted
372	Workshop control and monitoring using web	JENKOLE J., BUTALA P., SLUGA A.	Faculty of Mechanical Engineering in Ljubljana	Slovenia	Accepted
373	The impact of a mechanical press on the accuracy of products and the reliability of tools in cold forging	KRUŠIČ1 V., ARENTOFT2 M., RODIČ2 T.	Iskra Avtoelektrika1 d. d. Technical University of Denmark2 C3M d. o. o.3	Slovenia1,3 Denmark2	Invited paper
374	A study of abrasive water jet machining of aluminium with garnet abrasives	KHAN A., MUNAJAT N. B., TAJUDIN H.	International Islamic University Malaysia	Malaysia	Accepted
375	Robust, shortened process sequences for sheet light weight parts	GEIGER M., MARKLEIN M., KERAUSCH M., CELEGHINI M.	University Erlangen – Nuremberg Chair of Manufacturing Technology	Germany	Keynote paper
376	Intelligent prediction of stamping tool costs	FICKO M., BALIČ J., PAHOLE I.	Faculty of Mechanical Engineering in Maribor	Slovenia	Invited paper
378	Tooling Support for Magnesium Castings in Aeronautics Applications	BOTOLIN1 L, WENDT2 A., WEISS2 K., NARDIN1 B.	TECOS Slovenian Tool and Die Development Centre1 RWP GmbH Roetgen2	Slovenia1 Germany2	Accepted
379	Finite element modelling of forging processes using the flow formulation	ALVES1 M. L., RODRIGUES2 J. M. C., MARTINS2 P. A. F.	Instituto Politecnico de Leiria Departemento de Engenharia Mecanica1 Instituto Superior Tecnico Departemento de Engenharia Mecanica2	Portugal	Accepted
380	Cost Engineering - a necessity for survival in Europe	RAJKUMAR R.	Cranfield University	UK	Keynote paper
381	High Performance Cutting (HPC) Tools for Improving the Machining of Die & Mould Applications	GOLDBERG1 M., WERTHEIM1 R., MENARD2 J.	R&D, ISCAR Ltd1 ISCAR SLOVENIJA2	Israel Slovenia	Invited paper
382	Cost efficient stabilisation of metal forming processes	KUZMAN K.	University of Ljubljana, TECOS	Slovenia	Keynote paper
383	Apprication of Thin Hard Coarting to Forming Tools	DOHDA1 K., TSUCHIYA2 Y.	Gifu University, Department of Mechanical Systems Engineering1 Toyota Central R&B Labs., Metallic Material Laboratory2	Japan	Invited Paper
384	Micro - punching with vibrating punch	PRESZ W.	Warsaw University of Technology, Institute  of Material Processing	Poland	Accepted
385	Specific demands for material characteristics for producing trailskates	KOCOV1 A., TUTTLE2 M. E., LABOSSIERE2 P, GATES3 P.	University Št. Kiril I Metodij Faculty of Mechanical Engineering1 University of Washington Department of Mechanical Engineering2 GateSkate, Inc.3	Macedonia1, 2 USA3	Accepted
386	Analysis of the stress-strain condition of the wire drawing’s die by using FEA	KOCOV A., DUDESKI L., LAZAREV I.	University Št. Kiril I Metodij Faculty of Mechanical Engineering	Macedonia	Accepted
387	Simulation in Microforming	ENGEL U., GEIβDÖRFER S.	University Erlangen Nuremberg	Germany	Keynote paper
388	Shear and dimension stability effects in injection moulding	SILVA C., VIANA J. C., CUNHA A. M.	University do Minho	Portugal	Invited paper
389	One approach to rapid foundry tooling	ĆURIĆ D.1 , STANOJEVIĆ M.2	Fundry “Novi život” Zenica1 Mechanical Faculty Banja Luka2	Bosnia and Herzegovina	Accepted
390	Why we need a classification of injection moulding processes?	ČATIĆ I.1 , JOHANNABER F.2 , BLAŽEKOVIĆ N.3, BUJANIĆ B.1	University of Zagreb, Faculty of Mechanical Engineering and Naval Architecture1 K-Johannaber2 PAN Papirna industrija d. o. o.3	Croatia1, 3 Germany2	Invited paper
391	Cost engineering  - tools for achieving competitive advantage	FILIPAN B.	Gorenje Orodjarna d. o. o.	Slovenia	Accepted
392	Slovenia in the European Union - a challange and an opportunity for Slovene  tool makers	KUZMAN K.	University of Ljubljana, TECOS	Slovenia	Keynote paper
393	Analytical, numerical and experimental modelling and simulation of backward extrusion force on AlMgSi1	BARIŠIĆ B., CAR Z., CUKOR G., MIKAC T.	University of Rijeka Faculty of mechanical Engineering	Croatia	Accepted
394	Design adaption system for toolmaking	VALENTINČIČ1 J., BRISSAUD2 D., JUNKAR2 M.	University of Ljubljana, Faculty of Mechanical Engineering1 Institut National Polytechnique de Grenoble	Slovenia1 France2	Invited paper
395	Multi-scale and multi-physics analyses of material forming processes	RODIČ1, 2 T., KORELC3 J., STUPKIEWICZ4 J.,  LENGIEWICZ4 J. , DUTKO5 M., ŠUŠTAR1 T., GREŠOVNIK1 I., PRISTOVŠEK1 A., ŠUŠTARIČ1 P., CUKJATI1 D., HARTMAN1 S.	C3M d. o. o. Centre for Computational Continuum Mechanics1 Faculty of Natural Sciences and Engineering, University of Ljubljana2 Faculty of Civil and Geodetic Engineering, University of Ljubljana3 Polish Academy of Sciences, IPPT4 Rockfield Software Ltd., Technium5	Slovenia1, 2,3 Poland4 UK5	Invited paper
396	Toolmaking as a key to higher competitiveness with innovations	NAVODNIK J.	Navodnik d. o. o.	Slovenia	Invited paper
397	Business improvement with information solution e-ToolFactury	BABIČ1 V., ŠTEFANČIČ2 J., ŠTEFANČIČ2 S., VRBANČIČ2 A.	Eta Cerkno1 d. o. o. Genis2 d. o. o.	Slovenia	Accepted

Back | TECOS